1
00:00:04,000 --> 00:00:05,000
Good morning, friends.

2
00:00:06,000 --> 00:00:14,000
Today, I will tell you how to interface a relay module with the Nomaka.

3
00:00:16,000 --> 00:00:30,000
So over here we have VXI means by firewall and this is ground and or here we are using to Gilpin's the

4
00:00:30,000 --> 00:00:32,000
PIN number seven and number eight.

5
00:00:33,000 --> 00:00:47,000
So on the relay module, we have Bordelais and over here we have another is ground and two and signals

6
00:00:47,000 --> 00:00:49,000
from the Omegle.

7
00:00:49,000 --> 00:00:52,000
Right now I'm using all digital pens.

8
00:00:52,000 --> 00:00:54,000
You can operate using analog pen.

9
00:00:54,000 --> 00:01:02,000
Also in the separate video, I will tell you or in the continuation of this, I will tell you how to

10
00:01:02,000 --> 00:01:07,000
operate with Delphin and how to operate with analog.

11
00:01:07,000 --> 00:01:10,000
So right now, I'm using the pen.

12
00:01:10,000 --> 00:01:19,000
So first you just go to software part and over here you have to just open and over here you have to

13
00:01:19,000 --> 00:01:21,000
select the component.

14
00:01:22,000 --> 00:01:27,000
So in this case, my computer is seven and you have to just close.

15
00:01:28,000 --> 00:01:36,000
And in this you have to just tape like this does signal because we have to generate a signal in this

16
00:01:36,000 --> 00:01:36,000
case.

17
00:01:37,000 --> 00:01:43,000
So just to connect this and I am making a copy of this because in this case, I have to generate all

18
00:01:44,000 --> 00:01:45,000
those signals.

19
00:01:46,000 --> 00:01:58,000
So as you see, I just connect these and I just take a simple Ed handler to handle the error and take

20
00:01:58,000 --> 00:02:05,000
away loop for continuous rerouting of this continuous fighting, not reading in this case.

21
00:02:06,000 --> 00:02:10,000
And over here you have to just select the PIN number.

22
00:02:11,000 --> 00:02:20,000
So my PIN number is seven and over here you have to just select the value.

23
00:02:21,000 --> 00:02:33,000
And over here again, the PIN number eight and I just take to push buttons to push button one and push

24
00:02:33,000 --> 00:02:34,000
button two.

25
00:02:36,000 --> 00:02:46,000
So here this is my relay one and this is my relay too.

26
00:02:46,000 --> 00:02:51,000
OK, so you have to just arrange these.

27
00:02:53,000 --> 00:02:55,000
Not like this.

28
00:02:55,000 --> 00:02:56,000
Like this.

29
00:02:56,000 --> 00:03:06,000
And here the PIN number seven goes to this and over here we have to control you.

30
00:03:07,000 --> 00:03:15,000
And I just take two signals that the relays on or off.

31
00:03:17,000 --> 00:03:31,000
OK, so over here, my relay one output and this is my relay to output of.

32
00:03:33,000 --> 00:03:42,000
OK, so just connect these relay one is connected to this and two is connected to this control.

33
00:03:42,000 --> 00:03:53,000
You minimize the space and when you hit on one button, so first you have to just install the interfacing

34
00:03:53,000 --> 00:03:56,000
fired using maker hub.

35
00:03:58,000 --> 00:04:08,000
So over here, as you see already, select the board next then.

36
00:04:08,000 --> 00:04:10,000
Com for next.

37
00:04:11,000 --> 00:04:13,000
Next activity.

38
00:04:13,000 --> 00:04:28,000
Take hardly 30 seconds for interfacing file as you see, just finish this task.

39
00:04:35,000 --> 00:04:40,000
And they don't run, but when I say don't run button.

40
00:04:42,000 --> 00:04:52,000
And over here, I just right now boarded up entire on all of them on.

41
00:04:53,000 --> 00:05:00,000
Oh so right now using this, you can operate these relays.

42
00:05:01,000 --> 00:05:09,000
OK, so this is how you can interface a module with Ardino makeup.

43
00:05:09,000 --> 00:05:16,000
So this is the switching of related to and this is the switching relay one.

44
00:05:16,000 --> 00:05:27,000
So this is how you can generate multiple signals using Ardino Mega, as you see right now, both are

45
00:05:28,000 --> 00:05:35,000
condition on relay do is on little one is also on as you see Allouni glow.

46
00:05:36,000 --> 00:05:42,000
OK, so this is how you can interface a relay module with already know mega.

47
00:05:44,000 --> 00:05:44,000
Thank you.