So once you are extreme, generation is complete, you know, again, this will take of the top rate,
so allow this process to complete because we are performing synthesis, implementation and imitation
of a good swim.
OK, in a single step.
So this would be a finite amount of paint.
And once this is completed, we just need to close this window, right?
Then we will not be programming our refugees on what we are doing because we will not be utilizing AI
naively right now in our school whenever we are in situations where you want to arm and I lean to design.
There probably you have a situation where you will be programming your FPGA from all.
The rest of the chips will just be performing the programming of an FPGA from a sticky old.
Right.
So go ahead.
Do a fight.
You have an expert.
This is the first step that you'll be performing after you compete days off of it.
So explore tired of it and do not forget to include the right.
You just include a bitstream.
Click OK.
Then again, go to a fight.
I know you could click on launches sticky.
OK, set the default option, OK, and then click OK.
So this will automatically launch and it's sticky.
OK, where we will be writing our application and then verifying whether it is working on to an FPGA.
Now, remember, we have an armed subject, right?
So when we complete development of a sequel, the first thing that we'll be doing is to program and
execute you and then we are allowed to execute.
The secret to Argosy, right?
So once you are inside and is digging, you'll be finding a series of fight, which we'll be discussing
later on.
So without worrying much about a file, go to fight, then click on new and the new application project
will be created.
So this will be the first project that will be checking the gene in configuration is successful or not.
So we'll just be naming this ad sync configuration will be selecting the language type, do we see and
the board support package will be created based on NEBE that is in conflict base, right?
So click next.
Do not click finish because we want to select the correct template, just click next.
And the template that will be utilizing is an Halloway template.
So selecting Halol and click finish.
Now this will add a template where we could start working immediately with and you are ready for it.
Right?
So if you just explode the thing config folder that is denied, you have a small step.
Just go to a two step and then you have an halloway right here.
We'll just be modifying the Halloway with the same configuration is successful, and the function that
we'll be utilizing is still retain a right.
So this is the most efficient way to interact with your serial console.
Consuming a lesser amount of memory.
So we'll proceed with the ZIL printer and the string that will be adding is seeing the routine.
Configuration is successful.
This is the message that will be sending, right.
Now we want to execute this application, so just click on controls, so this will automatically be
through, right?
So if you analyze the console, once you click on controls, the program will be automatically checked
for any syntax error and then we will be building the program.
Right now, we haven't put Grandma FPGA yet, right?
So we go to this option where you see program FPGA.
So just click on that option that will automatically download a big file onto an FPGA since we already
exploded a big fight.
So the same file which we generated in a wheelbarrow will be downloaded on an next.
So once you complete this process, you have it done on your FPGA that should light up once you complete
the program.
Right now, here or so, you get the message that FPGA configure successfully with the bitstream.
That's the next step is to connect an SDK terminal because they will be interacting with the message.
Now you could have an external serial terminal, such as would be there.
You could connect to a specific port and then you could analyze the message that we are sending, right.
But here we do have a provision to do that is to give it that it's to get dominant.
So we need to just connect are both over here to click on this plus S..
We already know that we have connected FPGA board on the console and that will be recognized by default.
You just need to select for and click OK.
So if everything is fine, you able to see this message connected to the computer and you are working
at a rate of one one five two zero.
And this is exactly the same rate which we get by default on its debt to verify that you can just go
to the blog to say click on.
The bailout isn't going to be a spill configuration, and then we have a gentle tap, and here you could
see that the body that we have is one one five two seat right for.
We have you are zero also one one five two zero.
You like one.
Also, we have one one five two zero right now will go ahead and we will try to execute the right.
So to execute the goal, the process is very simple.
Just select the folder where you have your mean fight.
Right click right nice and then you have a launch.
So just click on that option.
And if everything goes fine, you're able to see sync to chain configuration is successful.
So this is an entire process that we'll be following, right?
From creating a blog design, generating a programming file, creating a see application, downloading
a programming file on it and then finally running an.