So I would assume the condition is successful now, we could just proceed and export the file, including
a victim to NSD.
OK, so we'll just go ahead and now launch in.
So these are the step that we've been following from the beginning, right?
So let's go ahead and create a new application project.
OK.
This will be naming you that interrupt and then switch early.
OK, so this will be the name of our application will be selecting an Halol template and we'll finish.
OK, so let's start writing and applications that the step is to initialize proof that it's OK, whatever
paper that we have in our block design and gender and to control it.
OK, so GSI itself is an independent block, so we need to initialize it similar to what we do with
the periphery before utilizing it, right?
So if you go ahead to end this fight, you could clearly see for a GPO, OK, for an AGP IP, the recommender
driver is Tupaea.
So similarly for which also the theme driver we need to utilize and to see if we have a driver SKU GSI,
right?
So if we go to an Helloworld first, we'll be including all the mandatory drivers so far to which we
have x GPIO looking for a gender in charge controller we have.
SC, you guys, you don't act right.
We also have I did experiment.
So there we will be finding all the addresses as early as head debating, right?
So we have a two x IP surprisingly not block present.
So we required by config.
OK, one for lady and one for Switch.
And this two will be pointed.
Similarly, we require two instance structure, one for an elderly and add the power switch, right?
Similar leave required a config structure for our general intra controller, which will be again a pointer
and the instant structure, which is right.
So we started the GPI initialization.
Now here we plan to utilize two different function one for initialization of all IP set, and that will
be initialization of control and control, right?
So we proceed, we declare to variable one for storing the initialization status off switch.
So we have added s active status and importantly, we have to set right.
We start with then first generation of our config structure, so we utilize lookup config files to the
device.
OK.
And since this belongs to anybody, so we'll be updating the value of any config structure.
Similarly, as we have up fixed structure, we will be utilizing C of G initialize function.
We will be passing the instance structure in the config structure and the ETC's rate, and it will basically
return status, which will be storing it.
And it's institute to a similar thing we'll be doing for our switch also to look up config switch device
that will be generating the Switch one fixed structure.
We will be utilizing such config structure and address along with an instance structure in and see if
initialize function to generate duties a state.
Now our agenda is to verify if both the status returns excess.
Texas, that is zero.
So see, does this due to sail boat and they together should return next this desexed?
As if that is the case, we could see which finality and it is successful.
Else we could just be mentioning that typo init three, right?
So let's proceed with the initial addition of a general into controller, so we have created one function.
OK, here we have a studious variable which will against to the value that is written by CFD initialize.
OK, so we see if you just look for the look up, all the functions that we do have a lookup config
function and we are required to pass a device ideology which could be found out from Parameter Dot.
So if you just go to an experimental or type two.
You have a dedicated section for.
Sue, I see where you could find out the device.
So this is the device aid that we supplied over here.
OK, so this need a config structure or a general controller and then that would be utilizing it and
see if you initialize along with the instance, structure and voice address to generate the street.
Now here also, we'll be checking whether citizens exist in Texas, and that is the case.
We will be mentioning that GSE initialization is successful.
And then.
We will be ready to move ahead.
Great.
So these are the two function of when we go to a mean function.
So here in a platform that initially is how you work, and then we have a GPO in which will initialize
our booth, the GPO benefit it and then you have legacy network, which will be initializing the gender
and control that.
Right.
So let's just go ahead and try to perform an execution of this.
So first, we need to program our 3G.
And once programming is successful, we will be correcting and instigate Dominion to the respect put.
So let me just go ahead and try to connect to call for greater one's connection is successful, will
be selecting a folder where we have our mean application dryness launch and.
So if everything is successful, you will see that switch and both are initialized successfully.
As with legacy, it is also successful, right?
So this completes our step three, that is we need to initialize if they fit it, as well as a general
control rate.
So this completes step, it now will proceed to step rate.